Headphone test: left, right, and whether your setup can play binaural beats
A binaural beat exists only when each ear gets its own tone. When a listener hears nothing, the usual cause is an output mixed down to mono by a phone setting, a single earbud, a Bluetooth call mode or an adapter. This page checks that in under a minute.
Do you hear a slow wobble, about ten times a second?
Now lift one side away from your ear. Does the wobble stop, leaving a plain steady tone?
Each ear is getting its own tone. The wobble needs both ears and vanishes with one, which is what a binaural beat does. Your setup can play binaural beats. Open the generator on its 10 Hz alpha preset →
That points to mono output. A wobble you can hear with one ear means the two tones are being mixed before they reach you. It is a real beat, but not a binaural one. Work down the list below, then run the check again.
The usual causes, most common first:
- Mono audio is switched on. On iPhone, iPad and Android, look for Mono Audio under Settings → Accessibility, in the audio or hearing section. The exact menu name varies by version and maker, so searching Settings for “mono” is quickest. Check the left/right balance slider next to it while you are there.
- Only one earbud is in, or only one is connected. Many wireless pairs switch to mono by themselves when one bud is in the case.
- Bluetooth is in its hands-free (call) profile. If a call is active or an app is using the headset microphone, the headset drops to a mono call mode. End the call or close that app, then reconnect.
- A mono adapter, splitter or cable is in the chain, or the plug is not pushed fully home.
- Spatial or surround processing is on. Turn it off for this.
- The volume is too low, or one side is much quieter than the other. Use step 1 to compare the sides.
If step 1 puts each tone in the correct ear and you still hear no wobble, read why binaural beats sometimes are not heard. A speaker-friendly alternative is the isochronic tones generator.
What this checks: whether your left and right channels reach you separately. It does not test your hearing; the hearing range experiment is the nearer tool for that, and it is not an audiogram either. The tool does not save your answers or send them anywhere, and every sound here stops by itself. Sessions in the main generator are free and capped at 20 minutes.
How to read the result.
Step 1 is the direct test: one tone, one ear. There are five things you can hear, and each one means something different.
- Left in the left ear, right in the right. Your channels are separate and the right way round. This is the result you want.
- Left in the right ear, right in the left. The headphones are on backwards, or, less often, a cable or adapter is reversed. For music and film this matters. For binaural beats it does not: the beat is the difference between the two tones, and it is the same difference whichever ear gets which.
- Each tone in both ears. The output is mono. Something between this page and your ears is mixing the two channels together. This is the result that stops binaural beats completely, and the mono settings section lists where to look.
- One side silent. A bud that is not connected, a balance slider pushed fully to one side, a damaged cable or a driver that has failed. Try another pair of headphones on the same device: if the silence moves with the headphones, it is the headphones.
- One side clearly quieter. See the last section; some causes are in the equipment and some are not.
Step 2 confirms it with the real thing. It plays 200 Hz to the left ear and 210 Hz to the right. With separate channels, most people whose two ears hear about equally notice a soft wobble or flutter about ten times a second that seems to sit inside the head. That wobble is not in either earpiece. Lift one side away and it vanishes, leaving a plain steady tone, because one ear alone has nothing to compare.
That is why the tool asks a second question after a “yes”. If your output is mono, the two tones are added together before they reach you, and the sum also wobbles ten times a second. That is a monaural beat: a real rise and fall in loudness, usually harsher and more obvious than the binaural kind, and still there with one ear. So hearing a wobble is not enough. A wobble that disappears when you listen with one ear is the sign that each ear is getting its own tone.
What this test cannot show.
It checks channel separation. It does not check your hearing. The tones here pass through your volume setting, your device and your headphones, none of which is calibrated, so nothing on this page can tell you how well either ear hears. If that is your question, the hearing range experiment lets you explore which pitches you can hear on your own equipment, and it says plainly that it is not an audiogram either. A real hearing test is done by an audiologist with calibrated equipment.
It also does not rate your headphones. A pair that passes is not thereby good, and a cheap pair that passes is exactly as suitable for binaural beats as an expensive one.
And passing says nothing about what binaural beats will do for you. Hearing the wobble shows the signal is arriving as intended. Whether listening to it changes focus, mood or sleep is a separate question, and the evidence on that is mixed and mostly from small studies; the research hub lists the trials and what each one found. Some people with separate channels barely notice the beat at all; the troubleshooting page covers that case.
The mono audio setting, and where to find it.
Phones and computers have an accessibility option that plays both channels in both ears. It exists for good reason: someone who hears with one ear, or who shares a single earbud, would otherwise miss half of a stereo recording. It is easy to switch on once and forget, and it silently turns every binaural beat into a monaural one.
Menu names change between versions and between phone makers, so treat these as directions rather than exact paths:
- iPhone and iPad. Open Settings, then Accessibility, and look in the audio section for Mono Audio. A left/right balance slider sits on the same screen.
- Android. Open Settings, then Accessibility, and look for Mono audio under an audio or hearing heading. The wording differs between Pixel, Samsung and other makers. Searching Settings for “mono” usually finds it faster than browsing.
- Windows and Mac. Both have a mono option in their Accessibility settings under Audio. On a computer, also check the sound output settings for a balance control, and turn off any spatial sound, surround or “enhancement” feature while you test.
Switch mono off, set the balance to the middle, and tap Left and Right again. If the tones now separate, that was the whole problem. If you rely on mono audio because of your hearing, leave it on: binaural beats need two working channels and two ears to compare them, and the isochronic tones generator is built for exactly the case where they are not available.
Spatial audio and head-tracking modes deliberately blend and move the channels to imitate speakers in a room, the opposite of what a binaural beat needs. Turn them off for this kind of listening.
Why binaural beats need two channels.
The beat is not in the recording. It is produced by your auditory system comparing two slightly different tones, one from each ear. Play 200 Hz on one side and 210 Hz on the other and neither earpiece contains anything that pulses; the ten-per-second wobble appears only where the signals from the two ears meet. How binaural beats work follows that pathway step by step.
It follows that anything which lets both tones reach the same ear removes the effect rather than weakening it. A speaker does this through the air, which is why binaural beats do not work without headphones, and that page explains what to play on a speaker instead. A mono setting does the same thing electrically. One earbud does it by leaving nothing to compare. Open-ear and bone-conduction headphones leak each channel across to the other side and blur it.
The requirement is separation, not quality. The headphones guide makes the case in full: any stereo pair that keeps left and right apart will do, including the earbuds that came with a phone.
Wired versus Bluetooth.
Both work. Bluetooth carries the left and right channels together in one stream, so any delay applies to both ears equally and the difference between the two tones is preserved. The common warning that Bluetooth compression spoils binaural beats is not correct, and you do not need a special codec.
What can go wrong on Bluetooth is a switch to mono, and it happens in two ways. Many true-wireless earbuds change to mono by themselves when only one bud is out of the case or connected. And every Bluetooth headset has a separate hands-free mode for calls that is mono and low in quality; a headset drops into it during a phone or video call and, on computers especially, whenever an app is using the headset’s microphone. If the tones here sound thin and arrive in both ears, end the call or close the app holding the microphone, and reconnect.
Wired headphones have fewer ways to fail and the failures are physical. A plug that is not pushed fully in can lose one channel or blend the two. A mono adapter, a cheap splitter, or an extension lead with the wrong kind of plug can do the same. If a wired pair fails step 1, reseat the plug first, then remove every adapter between the headphones and the device.
If one side is quieter.
Rule out the equipment first, because that part you can check yourself. Look at the balance slider described above. Then swap the headphones round, left earpiece on the right ear, and tap Left and Right again. If the quiet side moves to the other ear, the cause is in the headphones or the device: a worn driver, a blocked earbud mesh, a poor seal from an ear tip that does not fit. If the same ear is quieter whichever earpiece is on it, the difference is not in the equipment.
At that point this page has nothing more to offer, and it should not try. A difference between the ears can be as ordinary as earwax or a cold, or it can be a hearing difference that deserves a proper look. Neither can be told apart with a browser tone. An audiologist or your doctor can check it quickly, and a sudden change in one ear, or a difference that comes with ringing, pain, dizziness or a feeling of fullness, is a reason to be seen promptly rather than to keep testing at home.
For binaural beats specifically, a moderate imbalance usually makes the wobble fainter rather than absent. Do not compensate by turning the volume up. Keep it low; the safety page covers sensible listening levels.
Things people reasonably ask.
How do I test whether my headphones are left and right the correct way round?
Tap Left in the tool above. A short tone plays in the left channel only. If you hear it in your right ear, the headphones are on backwards. If you hear it in both ears, your device is playing mono and the two channels are being mixed together.
Why can I not hear binaural beats through my headphones?
The most common cause is mono output: a Mono Audio accessibility setting, a single earbud, a Bluetooth headset in its call mode, or a mono adapter. Spatial audio processing, very low volume and a large difference between the two ears can also hide the beat. Run the left and right test first; if each tone reaches both ears, the output is mono.
I hear a wobble in the binaural check. Does that prove my headphones are stereo?
Not by itself. If the output is mono, the two tones are mixed and produce a monaural beat that also wobbles ten times a second. Lift one side away from your ear: a binaural beat disappears and leaves a steady tone, while a monaural beat carries on in the one ear. Only the first result shows that each ear is receiving its own tone.
Where is the mono audio setting?
On iPhone, iPad and Android it is in Settings under Accessibility, in the audio or hearing section, labelled Mono Audio. The exact menu name varies by version and phone maker, so searching Settings for the word mono is the quickest route. Windows and Mac have the same option in their Accessibility audio settings.
Do Bluetooth headphones work for binaural beats?
Yes. Both channels travel in the same stream, so the difference between the two tones is preserved. The exceptions are earbuds that switch to mono when only one is connected, and the hands-free call mode, which is mono. End any call, close apps using the headset microphone and reconnect.
Does it matter if left and right are swapped?
For music, film and games, yes. For binaural beats, no: the beat is the difference between the two tones, and it is the same whichever ear receives which. What matters is that the two channels stay separate.
Is this a hearing test?
No. It checks whether your left and right channels reach you separately. Nothing here is calibrated, so it cannot measure how well either ear hears. If one ear seems quieter with the earpieces swapped round as well, that is a question for an audiologist or your doctor.
Are my answers saved?
No. The tool does not store your answers or send them anywhere; they only change what the page shows until you close the tab. The site itself uses analytics as described in its privacy policy.